Automatic and manual setup of DVB-T2 digital channels can be done independently; for this it is not necessary to seek help from specialists.

How to set up DVB-T2 on your TV? The setup process is suitable for almost all receiver models. The design of windows, the names of buttons and menu sections may vary, but the general algorithm is approximately the same for everyone.

Connecting a device that supports the DVB-T2 standard to digital television and setting it up is not at all difficult. To do this, just insert the cable into the appropriate connector and perform some simple manipulations to configure the channels. If you are using an outdated TV model that does not support receiving this type of signal, you will need to purchase a special set-top box.

The TV must have a special input for connecting an antenna, as well as a tulip-type connector and an input with a video output (scart). If your TV has an HDMI input instead of a SCART connector, then this is a better option.

If you can make a double connection – both via the “tulip” and via HDMI, you will be able to switch from one cable to another. It is best to watch via HDMI, because... In this case, a higher quality image is obtained.

The distance to the transmitting station (tower) matters. Most often, to effectively tune a TV, it is recommended to install an outdoor antenna with an amplifier, and in city houses on the 4th-5th floor you can use an antenna with a “mustache” or in the form of a frame without an amplifier, but with the “signal amplification” option on the TV set-top box.

A receiver is a device designed to receive a signal and transmit it to a TV. The signal source can be a satellite dish, antenna, or the Internet. Connection digital set-top box to the TV can be done either directly or via DVD or via a monitor. But in this case you may need a special adapter.

How to connect to a TV and set up a receiver (digital receiver)

1. Remove the device from the box and remove the protective film. The film must be removed, otherwise the device will constantly overheat.
2. Cut off the protective sheath from the TB cable approximately 1.5 cm long from the end (both ends). Stripping the sheath must be done very carefully so as not to damage the shielding film that protects the central conductor.
3. Carefully peel back the shiny protective film and screw the “F” connectors to the wires.
4. Connect the cable to the TV and set-top box.
5. Insert a bunch of “tulip” wires into the connectors of the TV and set-top box.
6. Connect the antenna to the TV. The antenna must be installed on an external wall of the house or on a balcony. After this, you need to move on to the actual setup.

To configure the DVB-T2 set-top box, you need to click on “Menu” on the control panel, and then go to settings. If the country is not specified by default, you must select it. You also need to select the region, language, image format, search mode.

After that, select the signal standard. By default, DTV-T/T2 is installed - this is analog and digital television. If this setting is not changed, the TV will search for both channels.

The program will prompt you to choose automatic or manual settings. You need to select automatic and click on the “Ok” button.

After this, the TV itself will search for all available paid and free channels. After completing the search, click on the “Save” button.

If “DVB-T/T2” is set in the “Search mode” item, then the device will independently find all those channels that are available in your region. But this is only possible if you already have a working antenna installed, which is directed towards the transmitter.

Digital terrestrial television channels of the DVB-T2 standard

If you bought a TV, antenna and set-top box just now, then when you open the welcome window, you need to click on the “Menu” button on the control panel. Next: “DVB-T setup” -> “Channel search” -> “Search mode”. Here you can both find the channels themselves and set the frequency.

To simplify the search process, you can first go to a special website with information to find out what frequencies the channels are broadcast on in your city.

If the antenna is directed correctly, then after a few seconds the “Signal Strength” and “Signal Quality” scales will be filled. If the level is good, then you need to click on “Search”, and the device will perform the adjustment itself.

If you don't know the right direction antenna, you can rotate it very slowly and smoothly. In this case, you need to carefully look at the scales of intensity and quality. Once these scales are full, secure the antenna in this position and perform a search.

This is one of the most simple ways set up your digital TV yourself. If automatic tuning turned out to be ineffective - the set-top box found few channels (or even did not find them at all), then you need to use manual tuning.

To do this, you need to delete all those channels that were found earlier. After that, select the manual search mode in the same way. A window will appear on the screen. In it you need to set the frequency on which all channels in your city are broadcast. You can find out the frequency on the Internet or from your service provider.

After the channels of the first multiplex have been found, you will need to find out the frequency for the second multiplex and start the manual search again. You can find many channels this way.

Checking the signal quality

To make sure that everything is done correctly, you need to find the “INFO” button on the receiver. (In some models, this button has a different name. To determine which button is intended for checking the signal quality, you need to look at the instructions.) This button must be pressed 3 times, as a result of which a window should appear on the screen with information about the signal quality, number channel, frequency and encoding. If the first two parameters are greater than 60%, this means that the signal level is acceptable.

If the signal is of poor quality (constantly changes its level) and shows 30% of the full signal, then the image quality will be very poor. In such cases, it is necessary to either raise the antenna higher, or install it in another place, or simply strengthen the signal.

If the TV can receive several multiplexes, you need to check the signal quality on each of them, because they work with different transmitters. It may well be that the signal will be good in one multiplex, but not in another.

Instructions

Transfer speed – 6900 sim/sec.
If you want to search for HD quality channels, change the frequency value to 338 MHz.

After installing and launching any of the above programs, you will see a menu for accessing hundreds of channels, to view which you do not need to make any additional settings - just select any of the channels and start watching. The interface of all programs is intuitive and it will not be difficult for even novice users to get used to it.

Video on the topic

Sources:

• how to set up internet tv

Those who use the Internet can perform network scanning. This will make the job safer and more reliable. carried out using special programs. For example, The Network Mapper, or Nmap for short, is an excellent utility for scanning networks. It has several scanning methods.

You will need

• Personal computer, The Network Mapper program

Instructions

To specify the hosting to be scanned, specify its name or address on the command line after specifying the options. To scan IP subnets, enter the parameter "/" after the name or IP address of the host that will be scanned.

You can search manually: select the “Manual channel search” subsection in the “Menu”. The “Reset Channels” function will delete all previous channel settings. You can also sort channels, group lists, or move a channel to . This is done through the “Sort Channels” option. Confirm each innovation with the “OK” button.

If you want to watch Electronic Program Guides (EPG), press the "EPG" button on the remote control. The screen will show 2 lists: at the top - a list of channels, at the bottom - a list of programs for the channel. To move through the list, use the “up” and “down” control buttons on the remote control. To exit the “EPG” menu, press “Exit” on the remote control.

note

Some TVs do not have an RCA connector, then select the SCART/SCART connector.

Sources:

• set up digital channels on your TV

TV- tuners are special devices that allow you to view cable or broadcast television on a personal computer. Currently, you can see many types of TV tuners on sale, but the setup for all of them is almost the same.

You will need

• - TV tuner;
• - driver;
• - a program for viewing a TV signal.

Instructions

Select TV tuner. This stage is perhaps the most important thing in setting up the device. The fact is that not all TV tuners may be suitable for your computer, especially if they do not have own program to watch the video. There is a device with an internal board, connected through a free Ethernet port on the router, and connected to a USB or IEEE 1394 port on the computer. Determine which type is suitable for your PC or laptop. If necessary, purchase a special adapter.

Connect the TV tuner to your computer or laptop. This step depends on what type of device you purchased. If you doubt your actions, read the operating instructions that should come with the TV tuner. Check that the connectors are connected correctly.

Turn on your computer or laptop and insert the driver disk that came with the TV tuner into the drive. If there is no such disk, then you can download the necessary files on the Internet on the device manufacturer’s website. If you have the Windows 7 operating system installed, then in some cases it will prompt you to download the required updates.

Install software to watch TV channels. It is on the disc sold with the TV tuner. If you don’t have one, you can configure your device for Windows Media Center or download a suitable viewer on the Internet. In the first case, you need to check the compatibility of the TV signal transmitted by the TV tuner and received by Windows Media Center. You can find similar information on the website http://windows.microsoft.com/.

Connect the TV tuner to your cable TV or antenna. Launch the program to receive a TV signal and press the channel scan button. If you completed all the previous steps correctly, a list of television channels will appear. Otherwise, check that the TV tuner is connected correctly.

Video on the topic

Sources:

• setting up a TV tuner

On computer can be viewed TV any type - cable, satellite, Internet TV. Each of these types of TV has its own advantages and disadvantages, but if we talk only about the quality and stability of the video image, then we can arrange them in this order in descending order of characteristics - cable TV, satellite, Internet TV.

Go to LyngSat.com and view information on these satellites - signal parameters, beam coverage, data on the presence or absence of encryption, etc. If your home falls within the range of the signal and it is not encrypted, purchase equipment that allows you to view satellite TV. The kit includes a satellite dish, a C- or Ku-band converter, a DVB card of S or S-2 format, and an antenna cable. The parameters of the converter and DVB card are determined by the signal parameters - take this into account when purchasing equipment.

Mount the satellite equipment, configure it and record the signal with the DVB card tuner program. Information about all the details of the setup is abundant on the Internet. After fixing the signal, install on your computer one of the programs that can be used to view satellite TV (ProgDvb, etc.), and scan the satellite with it. The program will finish its work by creating a playlist of detected channels. Click on any of them and view satellite TV.

To watch Internet TV, it is advisable to have an Internet connection with a speed of at least 1 Mbit/s. Moreover, not only speed is important, but also connection stability. If you have a choice, choose a dedicated DSL line or a Wi-Fi router. You can, of course, also use a 3G signal - by connecting via a USB modem or mobile phone– however, with this Internet connection, video disturbances may occur during peak loads on the communication line.

After the Internet connection is established, download one of the programs for watching television. One of the best is RusTV Player. If you use this program, download the most latest version(currently this is RusTV Player 2.3). Install the program on your computer and turn on any of the many channels in the program’s playlist.

Please note the subscription price for this service, it should be competitive and acceptable to you. If you think that the prices are unreasonably high, you should look for another provider. Currently, for 50-100 rubles a month you can get up to a hundred television channels, and these prices should be the basis.

When choosing an operator, you should not think about the quality of the broadcast signal - with digital television it is impeccable, since the transmitted signal is digitized and does not contain interference. But the quality of the channels themselves, that is, their professional level, can vary greatly. Therefore the presence large quantity channels in itself does not mean anything; you need to carefully study their list. Do not forget that it must include federal channels, preferably at least ten.

When comparing the conditions provided by digital broadcasting operators, take into account the presence of additional functions in service packages. Modern cable television makes it possible to use modern interactive services, such as TV menus, video on demand, TV programs, etc.

The main part of the digital television market is occupied by cable network operators and satellite broadcasting companies. IN Lately they are beginning to be crowded out by the IP-TV system, or Internet protocol television - this technology transmits a television signal via the Internet. It is steadily developing, new solutions are emerging that allow the use of equipment available to customers. Considering that the cost of Internet traffic is constantly falling and transmission speeds are increasing, we can expect a rapid increase in the popularity of this type of television broadcasting.

MENU (SETTING) --> OPTIONS

Selecting a country, for example, Austria (there are no digital cable TV settings for Russia)

SETUP --> DIGITAL CABLE SETUP - select OTHER OPERATORS

Section AUTO SEARCH --> select CABLE

Subsection CABLE - setting up the search type. We set the data as in the photo and save (OK)

Execute

Search process: digital channels will be found first, then analogue ones

Video instruction

MENU (SETTING) --> CHANNELS --> AUTO SEARCH

DIGITAL CABLE SETUP --> OTHER OPERATORS

Choosing CABLE TV

Set the parameters as in the photo and click NEXT

Selecting a search by channel type (if you do not mark anything, digital and analogue channels will be found)

Search process

Video instruction

1. Press the button - "Menu"

2. select “Settings”

3. in the window that appears, select “Menu analogue. settings"

4. in the window that appears, select “Add TV signal”

5. in the table that opens, put a tick on the “DVB-C” line and go below and click “Start auto-tuning”

6. After searching for all digital channels, going to the main menu in the “Settings” item, the line “DVB-C setup menu” appears. By selecting this item, you can adjust the settings manually (set the frequency and speed).

The menu on your TV may differ from the model shown. In this case, you need to find tabs that are similar in meaning. If your TV asks for a search step, enter 8 MHz.

Instruction No. 1

First, we read the stickers on the back wall of the TV, where separately for each tuner (DVB-T and DVB-C) there is a list of countries in which, according to Philips, there is digital broadcasting (at the time the TV was released, but if you update the firmware through their official website, this list may change in subsequent firmware). If our country is not there, then we will have to put some other one from this list.

2. select - "Configuration"

3. select - "Install"

6. select - "Digital mode"

7. select - "Cable"

8. select - "Automatic"

9. click - "Start"

Instruction No. 2

1. Click on the icon - “House”

2. select - "Install"

3. select “Search for channels”

4. select - "Reinstall channels"

5. select - “the country indicated on the sticker on the back panel” (usually France, Finland or Germany)

6. select digital mode - “Cable (DVB-C)”

7. In the “Network frequency” line, enter the frequency

8. in the line “Transfer speed” enter

Setup takes approximately 5-10 minutes.

Instruction No. 3

1. In order to set up digital TV channels high definition for the vast majority of Philips models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Configuration” section

2. Select the Installation tab. After clicking OK, you will be taken to the second menu field, then go to the Channel Settings tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. Installations". Next you will see a message about updating the channel list, click “Start”

3. Select "Reinstall Channels"

4. In the Country section, you must select Finland; if this country is not in the proposed list, then select Germany

5. Since you are connecting to digital television via a DVB-C cable network, you must select “Cable”

6. Before you start searching for channels, select “Settings” to manually correct the search parameters

7. Set the baud rate to manual mode. In the tab, change the transmission speed manually from the control panel to the desired one. In some TV models, the flow rate is indicated in the “Character 1” tab; “Character 2” is left at 0.

8. Now set the network frequency to manual mode and enter the network frequency from the control panel

9. After clicking the done tab, you will again be taken to the channel launch menu, now you can start scanning

10. If you did everything correctly and saved all the changed parameters, then during the search your channels will be detected.

MENU --> CHANNEL

In the ANTENNA section select CABLE

In the AUTO SETUP section, the CABLE SEARCH PARAMETERS subsection is set as in the photo

Channel search selection: all, digital only, analogue only. Then --> NEXT

Channel search process

Video instruction

Instruction No. 1

If your TV model provides for the reception of digital channels, but there is no “DTV MENU” item, then first select another country - France, Switzerland, Sweden or Finland.

1. Press the button - "DTV"

2. click - "DTV MENU"

3. select - "Installation"

4. select - "Auto-installation"

5. click - "OK"

Setup takes approximately 5-10 minutes.

Instruction No. 2

2. In the window that appears on the TV, select the TV tab, press the OK button.

3. In the menu that appears, set the parameters TUNER MODE - CABLE, COUNTRY - RUSSIA.

4. In the window that appears, select the SEARCH CHANNELS tab and click OK.

5. In the window that appears, select the ATV and DTV option and click OK.

Since not all SONY models are equipped with a digital tuner for cable TV (DVB-C), you need to check the model of your SONY TV.

Models equipped with a DVB-C tuner are marked KDL-**EX*** or KDL-**NX*** - for example KDL-32EX402R2 the first 3 letters in the model name (KDL) indicate that the TV is “digital” . In models KLV-**BX***, etc. There are no DVB tuners.

1. Press the "MENU" button (for some models it is called "HOME" on the remote control (hereinafter referred to as the remote control). This button is usually of blue color.

2. Select the “Settings” item.

3. Find the “Digital Configuration” menu in the list of settings and enter it

4. Select "Auto search for digital stations"

5. A source selection window will open - select the TV connection type. Select "cable"

6. In the selection of scan type - select the "full scan" mode

6.1 Or select "Manual"

7. Click "start"

Wait until the TV finishes searching for channels.

Pay attention to the bottom of your TV's OSD menu. The bottom menu bar displays hints on which remote control buttons to perform certain actions in the TV menu.

Instruction No. 1

1. Turn off the TV and install the conditional access module. Turn on the TV. Go to the menu. Select the language Russian.

2. Go to the DTV manual setup tab and click OK

3. Enter frequency, modulation, symbol rate

4. After pressing the OK button, a search will begin and the channels should be found.

Instruction No. 2

1. To start setting, press the MENU button on the remote control.

2. In the window that appears on the TV, select the INSTALLATION tab, press the OK button.

3. In the menu that appears, select the AUTOMATIC CHANNEL SCAN tab, click OK.

4. Select the DIGITAL CABLE TV option and press OK.

5. In the window that appears, click YES.

After installation is complete, all available digital and analogue channels should appear on the TV.

Who among us doesn’t sometimes like to spend the evening blissfully dozing in front of the TV? We think that everyone allows themselves such weakness from time to time. And so that watching TV brings only positive emotions two conditions must be met: firstly, you should not turn on news channels too often, and secondly, the TV must be configured correctly. Today we’ll talk about how to set up digital and satellite channels on your TV.

How to set up digital channels on your TV?

So, you bought a new TV, or decided to connect cable television - or analogue - to your existing television receiver. In this case, the procedure for setting up the TV will be as follows:

1. First of all, we enter into an agreement with the provider you like that provides cable television services.
2. After the television cable is routed through the apartment, connect the cable plug to the corresponding connector on the TV. The first thing we see is that the TV shows the message “channels not configured.”
3. We take the TV remote control in our hands and press the “Menu” button on it.
4. Select the “Channel settings” section in the “Menu”.
5. In the “Channel setup” section, select the “Automatic setup” sub-item and click “OK”. After this, the TV will go into scanning mode and automatically find all available channels. It should be taken into account that in the automatic tuning mode, duplicate channels or channels with low image quality may appear on the TV: ripples, stripes, interference, with distorted sound or no sound at all. When the scanning process is completed, you will have to get rid of all low-quality channels manually by selecting the appropriate items in the menu.
6. We wait patiently for the TV to finish auto-tuning. If there are a lot of channels, this process can take a good five minutes. When autotuning is completed, exit the menu by pressing the corresponding button on the remote control.
7. If you do not need to configure many channels on your TV, you can use a function such as “Manual tuning”. In this case, it is possible to set the required frequency for each channel, but it will take some time to configure each channel separately.

We would like to draw your attention to the fact that we have provided an average algorithm for how to set up channels on a TV. The fact is that there are now a huge number of TV models, appearance their remote controls and menus may differ significantly from each other. More details step by step instructions You can find it in the “Operation Manual” that comes with each TV.

Make sure your TV has a built-in digital signal receiver.

TVs with a built-in digital DVB-C receiver

SONY BRAVIA:
Almost all models with letter indices D, S, W, X, V, E, Z and a diagonal size of 32 inches or more,
series:
3000/3500/4000/4020/4030/4050/4210/4500/4710/5300/5310/5500/5510/5600/5610/5710/5740

LOEWE:
Almost all models.

SHARP:
model: 46 (52, 65) XS1, LE700

PHILIPS:
series: **PFL****Н

Toshiba:
series:
AV633/RV633/AV635/RV635/XV635/V635/SV685/LV685

JVC:
series: LT32DC1BH, LT26DC1BH

Panasonic:
series: TX-P42G10

LG Electronics:
Attention: it is necessary in the search menu: Country - include Sweden.
LCD TV series:
LH2000 DVB-T/MPEG-4/DVB-C
LH3000 DVB-T/MPEG-4/DVB-C
LH4000 DVB-T/MPEG-4/DVB-C
LH5000 DVB-T/MPEG-4/DVB-C
LH7000 DVB-T/MPEG-4/DVB-C
LU4000 DVB-T/MPEG-4/DVB-C
LU5000 DVB-T/MPEG-4/DVB-C
PLASMA TV series:
PS3000 DVB-T/MPEG-4/DVB-C
PS7000 DVB-T/MPEG-4/DVB-C
PS8000 DVB-T/MPEG-4/DVB-C
PQ200 DVB-T/MPEG-4/DVB-C
PQ300 DVB-T/MPEG-4/DVB-C
PQ600 DVB-T/MPEG-4/DVB-C

SAMSUNG:
Decoding of SAMSUNG TV models:

DVB-C receiver is built into all models starting from 2009! (letter index B, C or D)
Before setting up, you need to set the following parameters in the menu:
Country - Slovakia or Slovenia, Auto search for digital and analogue channels, Source - Cable, Network.

You can obtain more complete and accurate information on the presence or absence of a built-in digital receiver from sales consultants at the place where you purchased the TV!

Parameters for setting up a digital television test broadcast
(test broadcasting of digital television is available only for subscribers of the “Basic” package)

If there is no network search, then enter all frequencies manually.
Other frequencies: 642, 650, 658, 666, 674, 682, 690, 698, 706, 714, 722, 730, 738, 746, 754, 762, 770, 778, 786, 794, 802, 810 MHz.

Setting up digital channels on Toshiba branded TVs*

Now you can fully enjoy the capabilities of your TV by watching high definition channels. Enjoy watching and bright emotions!

Setting up digital channels on LG TVs*

1. In order to set up high-definition digital TV channels for the vast majority of LG models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Options” section
2. Specify the country Finland or Germany
3. Now go to the “Settings” menu, “Auto search” item and specify the method of connecting to the TV “Cable”
4. Now in the window that opens, go to “Settings” and enter the following parameters: Search type fast Frequency (kHz) 642000 Symbol speed 6875 Modulation 256 Network ID: auto
5. If you did everything correctly and saved all the changed parameters, then during the search you will find more than 100 digital channels and radio stations
6. Important feature LG TVs have the “Automatic channel update” function. It must be disabled, otherwise the TV will periodically reset the channel list you have configured. Go to “digital cable settings”: Auto Channel Update: Off

*Your TV menu may differ from the model shown. In this case, you need to find tabs that are similar in meaning and enter the specified parameters

If it works, we are happy for you!

Setting up digital channels on Samsung TVs*

1. In order to set up digital TV channels for the vast majority of Samsung models, press the “Menu” button on the remote control. The TV menu will open, in which you will need to select the “Channel” section (Satellite dish icon). In the “Antenna” tab, specify the connection type as “Cable”. Go to the “Country” tab and select the “Other” option. The TV will ask for a pin code, if you have not changed it, you will see 0000
2. Go to “Auto Configuration” Signal source: Cable, You choose the type of channels at your discretion, you can find only digital channels or digital + analogue
3. Specify Search mode: Fast Net: Auto Ident. Networks:----------- Frequency: 642000 KHz Modulation: 256 QAM Transmission speed: 6875 KS/s Click "Search"
4. As a result of the search, you should find approximately 100 television and radio channels.

*Your TV menu may differ from the model shown. In this case, you need to find tabs that are similar in meaning and enter the specified parameters

If it works, we are happy for you!
Now you can fully enjoy the capabilities of your TV by watching high definition channels. Enjoy watching and bright emotions!

Tuning digital channels on Philips TVs*

1. To tune in to HD digital TV channels on most Philips models, press the “Menu” button on the remote control. The TV menu will open in which you will need to select the “Configuration” section
2. Select the Installation tab. After clicking OK, you will be taken to the second menu field, then go to the Channel Settings tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. Installations". Next you will see a message about updating the channel list. Click "Get Started"
3. Select "Reinstall Channels"
4. In the “Country” section, you must select Finland. If this country is not in the proposed list, then select Germany
5. Since you are connecting to digital television via the DVB-C cable network, you must select “Cable”
6. Before you start searching for channels, select "Settings" to manually adjust the search parameters
7. Set the baud rate to manual mode. In the tab, the transmission speed is manually changed from the control panel to 6875. In some TV models, the bit rate is indicated in the “Character 1”, “Character 2” tabs.
8. Now set the network frequency to manual mode and enter the network frequency 642.00 from the control panel
9. After clicking the “Done” tab, you will again be taken to the channel launch menu. Now you can start scanning.
10. If you did everything correctly and saved all the changed parameters, then during the search you will find more than 100 television and radio digital channels

General algorithms for setting up digital channels for various models of LCD TVs:

1. Click on enter menu (green button)
2. Select in the menu - “Channel” (icon “Satellite dish”)
3. Select - "Auto-tuning"
4. Select - "Digital"
5. Click - "Start"

First, we read the stickers on the back wall of the TV, where separately for each tuner (DVB-T and DVB-C) there is a list of countries in which, according to Philips, there is digital broadcasting (at the time the TV was released, but if you update the firmware through their official website, this list may change in subsequent firmware). If our country is not there, then we will have to put some other one from this list.

1. Click on the icon - "House"
2. Select - "Configuration"
3. Select - "Install"
4. Select - "Digital mode"
5. Select - "Cable"
6. Select - "Automatic"
7. Click - "Start"

Setup takes approximately 5-10 minutes.

Philips TV models 2011

1. Click on the icon - "House"
2. Select - "Install"
3. Select - "Search for channels"
4. Select - "Reinstall channels"
5. Select - “the country indicated on the sticker on the back panel” (usually France, Finland or Germany)
6. Select digital mode – “Cable (DVB-C)”
7. In the “Network frequency” line, enter the frequency 642.00 MHz
8. In the line “Transmission speed” we enter 6875
9. Next, select the line “Frequency scanning”

Setup takes approximately 5-10 minutes.

1. Press the button - "Menu"
2. Select from the menu - "Options"
3. Select - "Auto-tuning"
4. Select the country - "France, Switzerland, Sweden or Finland"
5. Select the signal source - "Cable"
6. Select - "Digital"
7. Click - "Search"

Setup takes approximately 5-10 minutes.

If your TV model provides for the reception of digital channels, but there is no “DTV MENU” item, then first select another country - France, Switzerland, Sweden or Finland.

1. Press the button - "DTV"
2. Click - "DTV MENU"
3. Select - "Installation"
4. Select - "Auto installation"
5. Click - "OK"

Setup takes approximately 5-10 minutes.

Since not all SONY models are equipped with a digital tuner for cable TV (DVB-C), you need to check the model of your SONY TV.
Models equipped with a DVB-C tuner are marked KDL-**EX*** or KDL-**NX*** - for example KDL-32EX402R2. The first 3 letters in the model name (KDL) indicate that the TV is “digital”. In models KLV-**BX***, etc. There are no DVB tuners.

1. Press the "MENU" button (for some models it is called "HOME" on the remote control (hereinafter referred to as the remote control). This button is usually blue
2. Select "Settings"
3. Find the “Digital Configuration” menu in the list of settings and enter it
4. Select "Auto search for digital stations"
5. A source selection window will open - select the TV connection type. Select "cable"
6. In the selection of scan type - select the "full scan" mode
   6.1 Or select "Manual"
   6.2 Next, enter the frequency 642.000.
   6.3 Leave the access code as “Auto”. Next, enter the symbol rate 6.875.
7. Click "get started"

Wait until the TV finishes searching for channels.
!!! Pay attention to the bottom of your TV's OSD menu. The bottom menu bar displays hints on which remote control buttons to perform certain actions in the TV menu.

Panasonic

1. Press the button - "Menu"
2. Select the item “Settings”
3. In the window that appears, select “Analog settings menu”
4. In the window that appears, select “Add TV signal”
5. In the table that opens, put a tick on the “DVB-C” line and, going down below, click “Start auto-tuning”
6. After searching for all digital channels, going to the main menu in the “Settings” item, the line “DVB-C setup menu” appears. By selecting this item, you can adjust the settings manually (set the frequency and speed)

If it works, we are happy for you!
Now you can fully enjoy the capabilities of your TV by watching high definition channels. Enjoy watching and bright emotions!